How to reduce manual calculation time in structural engineering projects

Checking one cross-section by hand takes about half an hour. Every model revision runs that procedure again, and the repeat passes are where the engineering hours actually go. This article breaks down which operations inside the recalculation loop can be automated and which stay manual.

Every Model Revision Triggers a Recalculation

A revised plate thickness, a relocated node, and an added stiffener. Any of these invalidates the results that came before it. Formally, every dependent element has to be rechecked. In practice the volume of rechecking gets capped by the project schedule.

Tech-Clarity’s survey of more than 220 manufacturers breaks down where engineering time goes: roughly 54% on design work itself, another 29% on working with outdated information. Once a change is made, updated data reaches the whole team in 4.7 to 10.3 days depending on product complexity.

That interval is the window in which part of the team is still calculating against a superseded revision.

A Profile Swap Carries Nothing Forward

Swapping IPE 300 for IPE 200 is one line in a specification. On the calculation side, it is a full repeat.

Buckling resistance under EN 1993-1-1 is written as Nb,Rd = χ·A·fy/γM1. The reduction factor χ follows from the relative slenderness λ̄ = √(A·fy/Ncr), and the critical force Ncr = π²EI/(Lcr)² depends on the second moment of area and the buckling length. A new profile changes the area A, the second moment of area I, the radius of gyration i = √(I/A), and the section modulus W all at once. No intermediate value from the previous run survives. Section classification starts over, and the buckling checks about both axes, the lateral-torsional mode and the axial-plus-bending interaction all follow it.

Hence a familiar sequence: the full finite element model takes weeks to build and solve, and only then does it emerge that the initial section choice was wrong from the start.

The Spreadsheet Has No Link to the Model

Manual calculation still runs mostly on spreadsheets. According to the Institution of Structural Engineers, 95% of professionals use them regularly.

Error rates in spreadsheets have been measured. A summary of field audits covering 367 operational spreadsheets found that 24% contained at least one error. In experiments where the developer worked alone, the share of cells carrying an error ran from 1.1 to 5.6%. That order of magnitude matches error rates in other simple but nontrivial cognitive tasks: writing prose, doing a calculation, writing a line of code. Nothing here points to a weakness specific to spreadsheets. It is the ordinary human baseline, and the spreadsheet does not catch it.

The same guidance flags reuse as a risk of its own: a file written for one project gets carried over to the next, usually without documentation or any record of validation.

A second problem has nothing to do with arithmetic. Change the geometry or the boundary conditions, and the stresses sitting in the spreadsheet do not update. No warning appears anywhere in the file.

Combination Count Is Set by the Code

The number of design combinations follows from the standard and grows regardless of how simple the structure is. Take a flat roof carrying four actions: permanent, imposed, snow and wind. Assessed to EN 1990 for a single wind direction, it requires 14 ultimate limit state combinations plus 13 characteristic, 10 frequent and 8 quasi-permanent serviceability combinations. Forty-five design cases.

From there the count multiplies: wind directions, imposed load patterns, seismic situations, and each variable action taking its turn as the leading one.

Exhaustive Checking Replaces Sampling

At those volumes, manual checking becomes sampling. The engineer picks the subset expected to govern, and the reliability of the outcome rests on that judgment being correct.

An offshore jacket model produces one utilization ratio per combination, per element, per check type, which adds up to tens of thousands of values. An envelope pulls the worst of them, but it drops the link to the combination behind each point, and recovering that link means going back to the raw results.

Dedicated structural verification software (https://sdcverifier.com/) removes the sampling step. The full set of combinations gets processed at once, and each recognized structural item can be evaluated across the defined combinations, with governing results linked to the load combination that produced them.

This processing has a technical limit. Summing the results of individual load cases after the solve is valid only for linear elastic analysis, where response scales with load. Geometric nonlinearity, plasticity, and one-way supports break that assumption. In nonlinear problems, every potentially governing combination is solved as its own load case, and the saving then comes from queuing the runs automatically rather than from superposition.

Results Move into the Code Check by Hand

The solver returns fields of stress, displacement, and force. The code works in other quantities: utilization ratio, section class, buckling length, detail category. Converting one into the other is manual work, and it opens a methodological gap.

A 2026 paper in Buildings records that structural analysis results are neither produced nor stored natively in a BIM environment, and it describes current transfer practice as manual and error-prone. Even the structural entities in IFC 4.3, the authors note, cannot systematically represent output broken down by section and by load combination. On a prestressed girder bridge test case, an automated pipeline moved 1,800 data entries across four element types with a full match.

Automated report generation brings the document in line with the current state of the model. A manually assembled report reflects the data revision that was current when the writing started.

Freed-Up Iteration Goes into Section Sizing

Manual sizing usually stops at the first option that passes. Comparing several workable options by weight means repeating the whole calculation cycle for each one, which rarely fits the schedule.

Automation turns that comparison into a series of runs across section parameters, with minimum weight at a utilization ratio below unity as the selection criterion. The checking problem becomes an optimization problem because additional iterations no longer cost engineering hours.

What Does Not Get Faster

Some work resists automation: 

  • Choosing the analysis scheme 

  • Assigning boundary conditions

  • Idealizing joints

  • Handling singularities

  • Judging mesh convergence. 

These steps happen before any code check begins, and they set the credibility of everything downstream. Automation speeds up the calculation cycle. It does not make the model physically representative.

The scale of the available reduction has been estimated from outside the industry as well. A McKinsey review covered 150 workflows across 25 architecture, engineering and construction domains. Up to 50% of nonphysical work in architecture and engineering is open to automation, compared to 39% for construction as a whole.

What remains is a matter of engineering judgment and does not scale with the level of automation. Cutting manual calculation is a reallocation: the hours that went into substituting numbers into code formulas and reassembling documents get returned to working through structural alternatives.




Next
Next

Angelo State selects Kovexa for two-year student AI skills initiative